Normas CETOP

R6H

Pipe couplings for hydraulic piping - coupling thread (ISO 6149)

R8H

Definitions and symbols of performance characteristics - pumps, motors and integral transmissions. (ISO 4391)

RP9H

Technical conditions of delivery

R10H

Hydraulic cylinder - Cylinder internal diameters and rod diameter - Sizes of threaded rods and ports - Nominal pressures - Piston strokes (ISO 3320, 3321, 3322, 4393, 4395, 7181, 8136, 8137, 8138)

R11H

Recommendations for installation, commissioning and maintenance of complete hydraulic systems. (ISO 4413)

RPI2H

Recommendations for starting, servicing and maintenance of hydraulic power pumps

RPI3H

Recommendations for starting, servicing and maintenance of hydraulic motors

RPI4H

Recommendations for starting, servicing and maintenance of complete hydraulic transmissions (ISO FDIS 4413)

RPI5H

Recommendations for starting, servicing and maintenance of hydraulic valves

RPI6H

Recommendations for starting, servicing and maintenance of hydraulic cylinders

RPI7H

Recommendations for starting, servicing and maintenance of hydraulic intensifiers

RPI8H

Recommendations for installation, commissioning and maintenance of hydraulic accumulators

R34

Couplings for fluid power hoses (ISO 12151)

R35H

Mounting surfaces for hydraulic directional valves (RP 121H)

R39H

Schedule of required data for hydraulic fluids

RP41

Hydraulic and pneumatic systems - Circuit diagrams. (ISO 1219-2)

RP47H

Recommendations for the design, manufacture and safe application of gas loaded hydraulic accumulators. (ISO 4413)

R48H

Evaluation of the anti-corrosive qualities of water based fire resistant fluids (ISO FDIS 4404)

RP55H

Schedule of fire resistant tests for fire resistant fluids

RP56H

Test method to determine the fire resistance of FR fluids using a CFR engine at variable compression speed (based on ASTM D 613-61T)

R58H

Hydraulic cylinders - 160 bar - Medium series - Mounting dimensions - Bores 25 to 500 mm (ISO 6020-1)

RP6OH

Specification for oil hydraulic piston rods (ISO 3320 & 3321)

RP62H

Definitions and symbols of the operating characteristics of gas-loaded hydraulic accumulators (ISO 5596)

RP63H

Square flange connections for hydraulic piping (ISO 6162, 6163, 6164)

RP64H

Effect of evaporation on flammability

RP65H

Manifold ignition test

RP66H

Wick test (ISO DIS 14935)

RP67H

Anti-wear vane pump test for hydraulic fluids

RP69H

Hydraulic fluid power - mounting surfaces for flow control, pressure control and check valves (RP12IH)

RP7OH

Identification code for the level of solid contaminant in hydraulic fluids (ISO 4406)

RP71

Quantities, symbols and units of the international system (SI) to be used for fluid power (ISO 1000)

RP72H

Evaporation test for fire resistant fluid type HFC

RP73H

Hydraulic cylinders - 250 bar mounting dimensions - bores 50 to 500 mm (ISO 6022)

RP75H

Fluids for hydraulic transmissions -mineral oils- classification (ISO 6743-4)

RP76

Outside diameters for tubes in fluid power applications (ISO 4397)

RP77H

Fluids for hydraulic transmissions - fire resistant fluids - classification (ISO 6743-4)

RP78H

Hydraulic cylinders tolerances (ISO 8131 & 8135)

RP80

Cone type connection – 24º- for fluid power tubes and hoses (ISO 8434-1,8434-4,12151-2)

R8IH

Compatibility of hydraulic fluids with elastomeric materials (ISO 6072)

RP86H

Guidelines for the use of fire-resistant fluids in hydraulic systems (ISO 7745)

RP87H

Hydraulic cylinders - mounting dimensions for rod end plain eye (ISO 6981)

RP88H

Hydraulic cylinders - mounting dimensions for rod end spherical eye (ISO 6982)

R89H

Fluids for hydraulic systems - mineral oils - stability corrosion test

RP9IH

Fluids for hydraulic transmission mineral oils – specifications (ISO DIS 11158)

RP92H

Statement of requirements for filters in hydraulic systems (ISO 7744)

RP93H

Anti-wear test for hydraulic fluids using an internal gear type steering motor

RP94H

Determination of particulate matter in hydraulic fluids using an automatic size analyzer employing the light interrup­tion principle (ISO/FDIS 11500)

RP95H

Recommended method for the bottle sampling of hydraulic fluids for particle counting. (ISO 4021)

RP96H

Hydraulic fluid power - cavities for two-portslip-in-cartridge valves (ISO 7368)

RP97H

Fluids for hydraulic transmission - fire-resistant fluids - specification (ISO DIS 12922)

RP98

Guidelines for the specification, selection and application of hydraulic reservoir air breather filters (ISO 7744)

RP99H

Hydraulic fluid power - modular stack and directional control valves – sizes 03 and 05 - clamping dimensions (ISO 7790)

RP100

Hydraulic and pneumatic fluid power glossary (ISO 5598)

RP101

Lexicon of terms from the hydraulic and pneumatic fluid power glossary (ISO 5598)

RP104H

Hydraulic fluid power - acceptance test for hydraulic cylinders (ISO 10100)

RP106H

Hydraulic quick action couplings (ISO 7241 –1)

RP108H

Hydraulic fluid power 2, 3 and 4 port screw-in-cartridge valve cavities (ISO 7789)

RP109H

Hydraulic fluid power - Filter elements - Low temperature integrity test

RP110H

Fluids for hydraulic transmission - Fire-resistant fluids - Category HFA -Specifications (ISO DIS 12922 also 7745)

RP112H

Fluids for hydraulic transmissions - Mineral oil category HV - Method for determination of shear stability

RP113H

Fluids for hydraulic transmission - Disposal methods for used oil/water emulsions

RP115H

Hydraulic fluid power - Four port and five port servo-valves - Mounting sur­faces (ISO 10372)

RP117H

Hydraulic fluid power - Flushing of hydraulic systems

RP118H

Guidelines to the contamination control in hydraulic fluid power systems

RP121H

Hydraulic fluid power - Mounting surfaces for flow directional, pressure control, check and flow control valves (ISO 4401, 5781, 6263, 6264)

RP122H

Viscosity Shear Stability of Hydraulic Oils (Taper Roller Bearing Rig)

RP123H

Classification of ecologically acceptable hydraulic fluids (ISO 6743-4)

RP124H

Procedure for the determination of the filterability of hydraulic and lubrication oils - procedure for dry oils (ISO DIS 13357-2)

RP4P

Pneumatic cylinders - Suggested data for inclusion as a minimum in manufacturer's sales and literature

RP5P

Specification for pneumatic cylinders

RPI9P

Pneumatic directional control valves - Recommended data for inclusion in manufacturer's sales literature

RP2OP

Pneumatic flow control valves - Recommended data for inclusion in manufacturer's sales literature

RP2IP

Pressure control valves

RP22P

Pneumatic shuttle, non-return and quick exhaust valves - Recommended data for inclusion in manufacturer's sales literature

RP23P

Pneumatic pressure intensifiers - Recommended data for inclusion in manufacturer's sales literature

RP24P

Pneumatic rectilinear piston type cylin­ders - Recommended data for inclusion in manufacturer's sales literature

RP25P

Filters and water traps

RP26P

Lubricators

RP27P

Air Dryers

RP28P

Connections - Recommended data for inclusion in manufacturer's sales literature

RP29P

Pneumatic quick action couplings - Recommended data for inclusion in manufacturer's sales literature (ISO 6150)

RP3OP

Pneumatic rotating and telescopic joints - Recommended data for inclusion in manufacturer's sales literature

RP37P

Recommended diameters for pneumatic tubes and hoses

RP38P

Guidance on relation between port threads and pipe hose diameters

RP40P

Hose couplings, claw type

RP41

Hydraulic and pneumatic systems - Circuit diagrams (ISO 1219-2)

RP43P

Pneumatic cylinders - 10 bar operating - operating conditions and dimensions - bores 32 to 100mm

RP44P

Pneumatic fluid power glossary (ISO 5598)

RP46P

Units for fluid logic components and systems to be used in manufacturer's technical sales literature

RP49P

Technological symbols for fluid logic and related devices with and without moving parts (ISO 5784)

RP54P

Specification for polyamide tubing 11 and 12 for pneumatic transmissions

RP57P

Pressure relief valves - Recommended data for inclusion in manufacturer's technical sales literature

RP68P

Rules for the identification of ports and operators of pneumatic control valves and other pneumatic components (ISO DIS 11727)

RP71

Quantities, symbols and units of the International System (SI) to be used for fluid power (ISO 1000)

RP76

Outside diameters for tubes in fluid power applications (ISO 4397)

RP80

Cone type connections - 24~ - for fluid power tubes and hoses (ISO 8434-1, 8434-4, 12151-2)

RP82P

Response time characteristics of pneumatic directional control valves (RP 111P)

RP85P

Characteristics of pneumatic components

RP105P

Acceptance test for pneumatic cylinders

RP107P

Fixed pivot bracket for pneumatic cylinders (ISO10099)

RP111P

Switching characteristics of pneumatic directional control valves and moving part logic components (ISO DIS 12238)

RP114P

Pneumatic valves, subplates for five-port valves with mounting surfaces in accordance with (ISO 5599-1)

 

Regresar